Extension Pipe Kit for Stoves
In stock
Extension pipe kit for stoves that makes it possible to install the stove further away from the tub.
Used between the stove and tub, if you want to move the stove further away from the tub. The package includes 2 pcs 75mm outer dimension PVC pipe 1m, 2 pcs rubber hose 10cm 75mm inner dimension, 4 pcs clamps 80-85mm.
Notice that maximum distance with these pipes is 1m.
Gasket for Plastic Tub
Out of stock
Gasket for plastic tub for sealing the 2 1/2″ lead-throughs with 79 mm hole in Kirami tubs, connected between the lead-through of the wall and the outside tightening part/nut so that the wall sits in the U groove of the gasket.
Adjustment Grids for Heaters
In stock
Air flow adjustment grid for Kirami heaters.
This grid fits Micu, Cult and Macu heater doors and also new Cube heaters from spring 2018 onward.
Ash Boxes
Ash Boxes are an excellent accessory for your hot tub. Emptying the heater’s ash compartment is easy when the combustion waste accumulated in the firebox can be dropped into an ash box through the grate hole. The ash box allows the combustion waste to be easily and quickly removed without shovelling: simply remove the box from the ash compartment and dispose of the waste appropriately. Made of acid-proof stainless steel, the ash box boasts excellent heat and rust resistance.
Ball Valve Kit
Out of stock
The ball valve kit for kirami hot tubs consist of three parts that are connected to the 2 ½ inch inside thread in a Kirami hot tub instead of the original Kirami drain valve. The hose connector in the kit can be used with the same kind of 38mm inside measured hose as the normal valve.
Grate
Grate used in all Kirami’s stoves.
The L-iron grate is used in Cube, Side, Tube and Tube XL heaters for improving the draught. It guides some air to prevent the firewood and charcoal from falling out of the stove. Measures 320 x 145 mm and 50mm high wall on the front side.
Grate Cradle
Using a grate cradle improves air circulation inside the heater, boosting heating efficiency. The grate cradle also makes the heater easier to clean, as most of the ash that accumulates inside the heater during heating can be removed by simply taking out the grate cradle. The part is only compatible with the CULT and MACU heaters.
Heater Furnace Air Guide Plate
Out of stock
The Heater Furnace Air Guide Plate is compatible with CULT and MACU heaters. This fire plate directs air flow in the upper interior part of the heater by forcing combustion gases from the back of the fire box to circulate up and to the front of the heater before entering the chimney. This allows more heat to be recovered from combustion, thus boosting the heater’s thermal efficiency. Heaters must not be used without a fire plate.
Heater Glass Door
Out of stock
Kirami Feed-Through
Out of stock
The Kirami feed-through part used inside hot tubs, can be closed with its own plug. Used at the bottom of the hot tub, for connecting heaters and filter feed-throughs. M6 brass internal thread on the inside and 2 1/2” external thread on the outside. Made of ABS plastic. A separate protective grate that is available in several colors is installed on the feed through part.
Kirami Grommet Plug
Out of stock
The Kirami grommet plug suits as a plug for Kirami’s lead-through. The plug can be used e.g. for closing the lead-through of a filter, when the filter is not in use. M6 brass outer thread, made of ABS plastic.
Kirami Magnesium Anode Rod
Out of stock
The Kirami magnesium anode rod protects your heater from corrosion. The heater has accurate place meant for the rod. It should be checked twice in a year and replaced when necessary.
Kirami’s hot tub heaters were outfitted with these anode rods in spring 2017. The magnesium anode rod protects your heater from the corrosion that chlorine and seawater can cause.
Middle Outlet Kit PSKT
In stock
Installing the Kirami middle outlet kit PSKT between the heater and the tub may help you place the tub on a terrace. The standard option for emptying the water out of the tub is on the opposite side from the heater. With a middle outlet kit, the tub can be emptied from the same side as the heater. The middle outlet kit is available for plastic tubs.
The kit contains all the parts you need to install an outlet valve between the heater and the tub. The product does not include a Kirami outlet valve; the outlet valve included with the hot tub is moved to the middle outlet. The tub’s discharge pipe is closed with a plug provided with the kit. Distance between the heater and tub will be 36cm after installing the kit.
Kirami Outlet Valve Kit
Out of stock
The Kirami outlet valve kit used in plastic Kirami tubs since spring 2014.
Protective Grate for Kirami Feed-Through
A protective grate for Kirami feed-through made in Finland. Protects the feed-through from large debris and prevents the insertion of fingers and toes, etc. into the feed-through hole. Includes a screw for attaching the grid to the feed-through frame.
Made of ABS plastic. Comes in blue, gray, white, and beige.
Woody feed-through
Out of stock
The woody feed-through part is designed for the 40-mm thick walls of Woody hot tubs, and is attached to the hot tub’s wall with four screws from the interior side and sealed with silicon.
Aluminium feed-through part, pipe external diameter 75 mm. Used to connect a CULT, CUBE or MACU heater to a Kirami Woody hot tub.